Kitchen cabinetry
shipped to Tamworth.
Every cabinet cut to your wall lengths and ceiling height, pre-drilled, labelled and freighted to Tamworth with the hardware bagged against the cabinet it belongs to.
The short answer
A Tamworth kitchen is quoted from your measurements and photographs, not from a site visit, and the quote is fixed and itemised with freight shown as its own line. It is cut in Rockhampton and ships south along the New England Highway. You choose flat packed or delivered assembled on the same drawing. Fitting is done by your own trades — our installation team works Central Queensland only.
What should a Tamworth kitchen be built to survive?
As the service town for the district, the housing here runs from century-old cottages to new estate builds, and almost none of it suits a catalogue cabinet width. Every run we cut is drawn to the wall it is going on. Genuinely cold winters on the tablelands, and the temperature swing is why we specify the edging we do.
What does delivery to Tamworth involve?
Your kitchen is cut in Rockhampton and freighted south along the New England Highway. Flat cartons are labelled to a numbered drawing, one per cabinet where possible, with doors and fronts wrapped separately and the Blum hardware bagged against the cabinet it belongs to. Assembled orders arrive as finished boxes, doors hung and adjusted, which takes more truck space and shows as a higher freight line. Both are on the same quote so the choice is a number rather than a guess.
Who fits it in Tamworth?
Your builder, carpenter or kitchen installer, plus a licensed plumber and a licensed electrician for their parts. Ask each for a licence number and check it yourself — in New South Wales that is NSW Fair Trading. Every order ships with dimensioned service drawings showing each waste, water point and outlet, so the trades rough in to the plan rather than to a guess. Our install guide sets out the three trades and the fixed order they work in.
Where should the cartons sit before the trades arrive?
Somewhere dry, flat and off a concrete slab. Packed panels are fine stored flat and stacked, and they are not fine leaning against a wall for a fortnight or sitting where a slab can wick moisture into them. A garage on timber bearers or a couple of pallets is ideal. Open the cartons and check them against the drawing when they arrive, then close them again.
What happens if something arrives damaged?
Check the delivery against the numbered drawing on the day it lands in Tamworth, before the truck leaves if you can. Count the cartons, look at the door and drawer fronts. If a panel is damaged or a carton is missing, photograph it and ring the studio the same day. A replacement is cut from the drawing we hold on file, so it matches the rest of the kitchen rather than being re-measured from scratch.
Can I change the drawing after I approve it?
Before it is cut, yes, and changes at that stage cost nothing but time. Once the panels are cut they are cut to your sizes and cannot be re-used on another job, which is why the approval step exists and why we would rather you took an extra week over it. Read the elevations as carefully as the plan: most late changes are about where a door swings or which side of the sink the dishwasher sits, and both are obvious on the elevation.
Where else do you ship in New England and the North West?
We ship to Armidale, Inverell, Glen Innes, Gunnedah, Moree, Narrabri, Walcha, Uralla and the rest of the region on the same route. The New England and the North West page covers the region, and New South Wales covers the state.
- Drawn to your measurements, not catalogue widths
- 18mm moisture-resistant board, laser-bonded edging
- Soft-close hinges and full-extension runners
- Pre-drilled and labelled per cabinet
- Service drawings for your plumber and electrician
- Fixed itemised quote, freight its own line
- Installation not offered in Tamworth
Kitchenettes for a granny flat, studio or short-stay unit start at $4,500 — see flat pack kitchenettes.
Building a second dwelling? Granny flat rules in New South Wales.
The specification
Built for this
climate, not a catalogue.
The seasonal swing here moves timber and board more than a steady climate does, and the joint that gives first is almost always the edge. Laser-bonded edging is fused to the panel rather than glued to it, so there is no seam to lift.
The same three questions decide any kitchen anywhere: board thickness and moisture rating, edging method, hardware brand. Ours are 18mm moisture-resistant, laser-bonded and Blum, and they are printed on every quote. How to judge a flat pack.
- 18mm moisture-resistant board
- Laser-bonded edging, no glue line
- Soft-close hinges and full-extension runners
- Cut to your drawing, not catalogue widths
- Pre-drilled and labelled per cabinet
- Fixed itemised quote, freight its own line
What goes inside it
Anyone can sell you boxes.
This is the part that takes knowing.
Carcasses and doors decide how long it lasts. The fittings decide whether you like using it — and most suppliers charge for them at the end. These are included in your Tamworth kitchen, not quoted as extras once the number is agreed. That is the difference, and it is the one most suppliers will not match.
Plate and pot racks
Pegs and rails inside a deep drawer so plates stand up and pots stop stacking into each other.
See how it works →
Pull-down wall basket
The top shelf of an overhead, brought down to where you can reach it. The shelf you stopped using becomes storage again.
See how it works →
Drawer organisers
Cutlery, knives and spices in fitted trays cut to the drawer, instead of a plastic tray that slides around in it.
See how it works →There are seven in all — see the full range.
No showroom. No account.
A person draws it.
Send the wall lengths, the ceiling height and a photo of each corner. A designer draws your kitchen to the room and sends the drawing back with a fixed, itemised quote — flat packed and delivered assembled, freight to your postcode on each.
- Nothing to pay to see the drawing or the quote
- Changes redrawn until the plan is right
- Cut only after you sign the drawing off
- Freight quoted as its own line, never folded in
Or call (07) 4863 5788 — you get the person who designs it.
Frequently asked
Tamworth — questions
If your question is not here, call the studio. We would rather talk it through than have you guess.
Ask us directly →Do you deliver flat pack kitchens to Tamworth?
Yes. Tamworth is served south along the New England Highway, and freight is quoted to your postcode as its own line on the quote rather than folded into the cabinetry price.
Do you install kitchens in Tamworth?
No. Our own installation team works Central Queensland only. In Tamworth your builder, carpenter or kitchen installer fits it, working from the dimensioned service drawings that ship with every order. Our install guide covers the three trades and the order they work in.
Should I order flat pack or assembled to Tamworth?
Both are quoted on the same drawing. Flat cartons ship for less and get through tight doorways; assembled arrives with carcasses built and doors adjusted so your installer is fitting rather than building. Over this distance most New England and the North West orders go flat.
Who can do the plumbing and electrical in Tamworth?
A licensed plumber and a licensed electrician, and you should check both licences yourself before they start. In New South Wales, NSW Fair Trading is the register to check against.
What board and hardware do you use?
18mm moisture-resistant board, laser-bonded edging and soft-close hinges and full-extension runners on every cabinet, in every state, with the hardware brand named on your quote. The specification is printed on your quote so you can hold it against anything else you are offered.
How long will a Tamworth order take?
It depends on the kitchen and the freight route, so it is stated on your quote for your job rather than guessed here. What you can plan around is the sequence: drawing, your sign-off, cutting, then freight.
Can I add pull-downs and organisers to a Tamworth kitchen?
Yes, and they are quoted per item rather than bundled into a package you did not ask for. Pull-down wall baskets, magic corners, tall larder pull-outs and drawer organisers can all go into a Tamworth order. If you order delivered assembled they are fitted before it ships; flat packed, they arrive with the cabinet they belong to.
Delivered assembled
The assembly is done
before it arrives.
Carcasses built square on a bench, Blum hardware fitted, doors hung and adjusted to even gaps. On site you are fixing finished cabinets to a wall, not building them on the floor. Your builder or installer levels it, fixes it and fits the benchtop, working from our drawings. Prefer to build it yourself? The same kitchen ships flat pack.
Laser-bonded edging, no glue line
Handleless rail on an assembled run
Gloss doors, adjusted to even gaps before delivery
Tamworth, NSW
Send us the dimensions.
We will send back a number.
A fixed, itemised quote for your Tamworth kitchen, flat packed and delivered assembled, with freight to your postcode on each. Nothing to pay to see it.